Configuration Manual

After unpacking, the gateway is ready to use, but requires configuration to adapt to the required functions. 
 Power supply 
 The device can be powered by connecting a power source to the terminal block:   
 
 Loosen or remove the screws on the terminal block. 
 Connect a 8–36 VDC power line to the terminal block. 
 Tighten the connections, using the screws on the terminal block. 
 Turn on the power source. 
 
 Note that the device does not have an on/off switch. It automatically turns on when it receives power. It takes a couple of seconds for the system to boot up. Once the system is ready, the RED LED will light up.  
 Power terminal block pin assignments are shown below:  
 
 
 Connecting the configuration port 
 To configure the device, firstly connect RX, TX and GND of device to TX,RX and GND of Atreyo TTL converter or any other TTL converter with 9600, 8, N, 1 parameter. 
 The pin assignment of the port is shown as above. 
 
 Note that RX of gateway should be connected to TX of USB-UART converter. And TX of gateway to RX of USB-UART converter 
 
 Inserting SIM card 
 Please refer drawing for proper SIM placement. 
 
 
 Connecting configuration application 
 
 Connect one end of the TTL converter to the window computer. 
 Open AG IoT Configuration application on window PC. 
 Select AG-201, Select COM port and configure port with 9600,N,1,8 and click open port After port connection, click connect. 
 Once the connection is established successfully, enter the password "atreyo" to access the configuration mode. This is the default password. 
 Click CONFIGON and configure device parameter, as shown below: 
 
 
 
 Beneral configuration 
 
 Reset the device parameters by selecting  Make default . 
 Initiate a device restart by clicking on  Restart . 
 Modify the password in the Device Password section; after entering the new password, click  Set Password . 
 To apply and save these changes in the device, click  Config OFF. 
 After configuring all parameters, remember to click Config OFF . 
 The device will automatically restart and operate based on the new configured parameters. 
 
 Serial interface 
 Go to Device option to view and configure serial parameter. To configure serial parameter: 
 
 Configure the b audrate , parity , data bits and stop bits . 
 Click " Set " to apply the chosen settings. 
 Click “ Get ”, to access the stored serial parameters from the device. 
 
 
 
 
 Fiels 
 Value 
 Comment 
 
 
 
 
 Baudrate 
 2400 | 4800 |9600 |14400 | 19200 | 28800 | 33600 | 38400 | 57600 | 115200 | 230400 | 460800 |921600 
 default: 9600 
 
 
 Data 
 8 | 9 
 default: 8 
 
 
 Parity 
 None | Odd | Even 
 default: None 
 
 
 Stop 
 1 | 2 
 default: 1 
 
 
 
 
 
 GSM parameter 
 
 Configure the APN , user , password . 
 Click " Set " to apply the chosen settings. 
 Click “ Get ”, to access the stored GSM parameters from the device. 
 
 
 
 Modbus 
 For Modbus command frame configuration, refer the table. You can add new modbus request string via the edit section. 
 
 
 
 
 Field 
 Value 
 Description 
 
 
 
 
 Slave ID 
 Integer[1...255] 
 Slave ID 
 
 
 Function code 
 Read Coils(1) | Read Discrete Input(2) | Read Holding Register(3) | Read Input Register(4)  
 Specifies the type of register being addressed by a Modbus request 
 
 
 Data structure 
 8bit INT | 8bit UINT  | 8bit HEX| 16bit INT |16bit UINT | 32bit float | 16bit HEX | 32bit HEX | Bool 
 Defines how read data will be stored 
 
 
 Start address 
 Integer [0 – 65535] 
 First Modbus register from which data will be read 
 
 
 Offset address 
 Integer 
 The starting address or position of a data element within a register or data block 
 
 
 Data length 
 Integer [1 – 30] 
 Number of Modbus registers that will be read during the request 
 
 
 Data length 
 Integer [1 – 30] 
 Number of Modbus registers that will be read during the request 
 
 
 Endian structure 
 
 2bit data – ABCD | BADC | CDAB | DCBA 
 16bit data - AB | BA 
 
 Select endian structure of data type 
 
 
 Trigger 
 - 
 Not available now 
 
 
 riggering time 
 - 
 Not available now 
 
 
 Polling time 
 integer [1..]in sec; default: 60Sec 
 Interval at which requests are sent to the server device. 
 
 
 
 
 By clicking ADD, you can add multiple Modbus request strings. 
 Click "Set" to save a single frame or "Set All" to save  all the Modbus request strings in the device. 
 clicking "Get" or "Get All", to access the saved Modbus strings in the device. 
 Additionally, you can delete, copy, and paste strings from the Navigate section. 
 Go to Modbus parameter section and set polling time of modbus data to the server by click on "Set". Also check polling time from device by click on "Get" 
 
 
 
 MQTT 
 
 Go to MQTT Parameter section, to add MQTT parameter.  
 Specify a server details, host and port. 
  If the broker requires, enter Client ID, Username, and Password. (optional). If not, enter NULL. 
  Specify the publish and subscribe topics. 
  Once you've specified all parameters, click "Set." 
 Click "Get", to access details of the MQTT parameters. 
 
 
 
 Save and restore 
 Easily configure the number of devices by loading a configuration file. Navigate to the Connection section, load the file by clicking  Load All , and load all configuration parameters by clicking Write All . 
 
 The application allows saving the configuration for later uploading to other gateways.  
 
 Save all configured parameters in a file by navigating to the Connection section and clicking  Save all . 
 After clicking "Save all", navigate to the Config section. From there, first you have to create config file by click on "Create config", once you create file, you can save it by clicking Save config . 
 And this file you can use for configuration of other AG-201 gateway anytime by click on  Open config.