AMB-16I-AC
AMB-16I is a digital input extender with high voltage range from 60V AC up to 500V AC. Input also support DC voltage in same voltage range. The power supply range is 8 to 36V and accept DC or AC voltage.

General information
Download technical specification
Technical Specification

Configuration manual
Features
Configurable device address (1 ~ 247) using 8 bit DIP switch, multi devices can be cascaded on RS485 bus
Configurable device baud rate (2400bps ~ 128000bps) using 4-bit DIP switch
TVS (Transient Voltage Suppressor) protection, effectively suppress surge voltage and transient spike voltage in the circuit, lightning proof & anti-electrostatic
Optocoupler isolated digital inputs, prevent interference from external high-voltage circuit
Reverse-proof circuit, prevent the circuit from being damaged accidentally by incorrect connection
DIN-Rail mounted plastic enclosure, easy to install, safe to use
3 LEDs for indicating the MCU status and signal transceiving status, also LED indication for power and inputs
Watchdog Timer
Protocol Description
MODBUS Protocol is a messaging structure, widely used to establish master-slave communication between intelligent devices. A MODBUS message sent from a master to a slave contains the address of the slave, the 'command' (e.g. 'read register' or 'write register'), the data, and a check sum (LRC or CRC).
Since Modbus protocol is just a messaging structure, it is independent of the underlying physical layer. In AMB-16I-AC is implemented using RS485 interface.
Modbus RTU Framing
The AMB-16I-AC module supports standard RTU Modbus protocol for getting the input status and setting/getting the relays status. RTU Modbus Protocol frame is illustrated below:
Start
Address
Function
Data
RC Check
End
≥ 3.5 Char
4 Bits
8 Bits
N*8 Bits
16 Bits
≥ 3.5 Char
Start is at least 3.5 char time of silent interval between master and slave to start communication
Address is a slave ID Address
Function is the function code of MODBUS protocol
Data is the appropriate data for function code
CRC is Cyclic Redundancy Check for Error Checking (here, CRC-16,Big Endian(ABCD))
End is at least 3.5 char time of silent interval between master and slave to start communication
Modbus Serial Port Parameter
Parameter
Option/range
Baudrate
9600 – 128000 configurable
ata bit
8
Parity
None
Stop bit
1
ID Configuration of Modbus Card
After setting Modbus and baudrate, the I/O card must be restarted by switching the power off and on.
User can set the slave ID address using 8 Bit DIP switch found on board. This allow 0 to 255 different IDs to be set. The number below the switches are added together and the result will be identifier of the device slave ID.
To set the slave ID 125, you need to turn ON switch 1,3,4,5,6,7 on DIP switch and OFF the others (In this, convert slave ID number 125 into 8bit binary form – 01111101, turn ON DIP switch 1,3,4,5,6,7 and turn OFF DIP switch 2,8) and so on…. 
Address 1–247 → valid slave IDs for individual devices
Address 0 → reserved for broadcast messages; all slaves receive it but no one replies 
Addresses 248–255 → reserved/unassigned (not permitted for standard device addressing)
Baudrate Configuration
User can set the baudrate using 4 Bit DIP switch found on board. To set baudrate, first turn off power supply of card. This allows to set baudrate between 2400bps to 128000bps as shown below table.
Baudrate
SW1
SW2
SW3
SW4
9600
OFF
OFF
OFF
OFF
2400
ON
OFF
OFF
OFF
4800
OFF
ON
OFF
OFF
14400
OFF
OFF
ON
OFF
19200
OFF
OFF
OFF
ON
28800
ON
ON
OFF
OFF
38400
OFF
ON
ON
OFF
57600
OFF
OFF
ON
ON
115200
ON
OFF
OFF
ON
128000
ON
ON
ON
ON
Modbus RTU Commands
The following commands (functions) were implemented in the Modbus RTU AMB-16I-AC.
01 (01 hex) Function code – Read Coils
Coils are mapped to outputs and discrete inputs are mapped to inputs. Coils read/write output status and discrete inputs read Input status. There are 4 inputs for reading-input 0 to input 3 which refer to input 1 to input 4 and coil 0 to coil 3 which refer to output 1 to output 4.
Note: For all below example, consider slave address – 0x01 will change with 8bit DIP switch.
01 (01 hex) Function Code – Read Coils
Read Coils command is requesting the ON/OFF status of coils. Read Coils command will return individual current outputs status. Also Read Coils Command will return sequentially outputs current status. 
Example of how to read output status are given below:
REQUEST FRAME –
01 01 0000 0008 3DCC
01 – The Slave Address (01 hex = 01)
01 – The Function Code 
0000 – The Data Address of first coil to read (0000hex = coil 0)
0008 – The total number of inputs requested (0008hex = 8 inputs)
3DCC – The CRC for error checking
RESPONSE FRAME – 
01 01 01 C9 91DE
01 – The Slave Address (01 hex = 01)
01 – The Function Code 
01 – The number of data bytes to follow (8 inputs / 8 bits per byte = 1 byte)
C9 – Input 0 to 7(Inputs), C9 hex = 1100 1001 (0 – ON, 1 – OFF)
91DE – The CRC for error checking
Modbus Exception Codes
Exception responses from either the master or a slave can result from data processing errors.
One of the following events can occur after a request from the master:
If the slave receives the request from the master without a communication error and can handle the request correctly, it returns a normal response. 
If the slave does not receive the request from the master due to a communication error, it does not return a response. The master program eventually processes a timeout condition for the request.
If the slave receives the request from the master but detects a communication error, it does not return a response. The master program eventually processes a timeout condition for the request.
If the slave receives the request from the master without a communication error, but cannot handle it (for example, the request is to read a register that does not exist), the slave returns an exception response to inform the master of the nature of the error.
Exception Frame:
Sn.
Definition
Description
1
Slave Address
The Slave Address of requested slave
2
Exception Function Code
Requested Function Code + 128 (0x80)
3
Exception Code
See in next table
4
CRC check
The CRC for error checking
Exception Codes:
Exception Code
Name
Description
0X01
Illegal Function Code
The function code received in the request is not an allowable action for the slave. This may be because the function code was not implemented in the unit selected. 
0x02
Illegal Data Address
The data address received in the request is not an allowable address for the slave.
0x03
Illegal Data Value
A value contained in the request data field is not an allowable value for the slave.  This indicates a fault in the structure of remainder of a complex request, such as that the implied length is incorrect. 

Safety information
Operating environment
The device is designed to be installed in clean, dust-free and insect-free places
Operating temperature: -25 ~ 65°C (-13 ~ 149°F).
Humidity range is 10% to 95% (non-condensing). Use the device in a dry environment.
Away from heat sources and direct sunlight.
It must not be exposed to acid fumes, salts and other chemicals.
The device must not be used in places where there is a risk of gas explosion.
This is open type device intended for installation in a final casing/panel that offers mechanical protection and protection against the spread of fire.
Use in inappropriate conditions may damage the device or shorten its life.
Electrical and power supply safety
The device is powered with a voltage in the range of 8-36V. Voltage up to 24V is considered safe. Be especially careful when supplying them with higher voltages.
Use only approved accessories
Use the supplied power adapter or a good quality certified power adapter with the correct supply voltage range and sufficient power.
Only use approved accessories like antenna etc.
Only a person with qualification and appropriate knowledge should install the device.
Malfunctioning and damaged device
Do not disassemble the device.
Only qualified personnel must service or repair the device or its accessories.
If water or other liquid has got into the device, or if it looks mechanically damaged, do not connect the device, but take it to an authorized service center. 
Radio frequency exposure
This device has been designed and manufactured not to exceed radio frequency energy emission limits set by regulatory agencies. To comply with RF exposure guidelines, the device must be used at least 20 cm away from a person's body. Failure to follow these instructions may result in exceeding the applicable RF exposure limits. This only applies to models with a built-in LTE modem.
What to do and what not to do
You are solely responsible for the use of the device and any consequences of its use.
Do not store or use the device in harsh environments such as dust, gases, oils, chemical vapors and damp places.
Do not throw the device and its accessories. Handle with care.
The device heats up during operation. Ensure proper ventilation.
If you need to dispose of your device, check your local regulations for recycling and disposal of electronics.
Route power, Ethernet, and antenna cables properly so that they cannot be accidentally pulled out.
The device should be used and kept away from small children.